Integrated Systems Scandinavia AB · Expertise for electronics professionals
ISS — Integrated Systems Scandinavia
Knowledge Center / Test & Measurement

Test & Measurement · 4 MIN READ

Aardvark vs Promira: Which I2C/SPI Tool Should You Choose?

Choosing between Aardvark and Promira? Compare their capabilities and learn which questions to ask before selecting an I2C/SPI tool for your next project.

In this article
Aardvark or Promira? Start with your applicationWhen Aardvark is a good fitWhen Promira is worth consideringFive questions to answer before orderingClock speed is not the same as test throughputOur recommendationDiscuss your application with ISSTechnical referencesAsk an ISS expert ↗

Aardvark or Promira? Start with your application

Choosing an I2C/SPI tool starts with understanding the device you need to communicate with. Bus speed matters, but so do signal voltage, operating mode and the way the tool will fit into your test workflow.

The Total Phase Aardvark I2C/SPI Host Adapter is a practical option for straightforward device communication. The Promira Serial Platform offers a broader range of capabilities through application-based configuration.

The right choice depends on what you need today—and what your next project may require.

When Aardvark is a good fit

Aardvark connects a computer to an embedded system over USB and supports both I2C and SPI master/slave operation.

Its specified master clock ranges are:

  • I2C: 1 kHz to 800 kHz.
  • SPI: 125 kHz to 8 MHz.

It is worth considering for tasks such as reading registers, sending configuration commands and communicating with devices during board bring-up.

For example, if your task is to configure an I2C sensor operating at 100 or 400 kHz, Aardvark is a candidate to evaluate. Check electrical compatibility, addressing and transaction requirements before selecting the complete setup.

When Promira is worth considering

Promira is designed around hardware with licensed applications that determine the available protocol features and performance.

Depending on the installed applications, it supports:

  • I2C master/slave operation up to 3.4 MHz.
  • SPI master operation up to 80 MHz and slave operation up to 20 MHz.
  • Single, Dual and Quad SPI.
  • Integrated level shifting for signal voltages from 0.9 V to 3.3 V.
  • USB and Ethernet connectivity to the host computer.

These are platform capabilities, not features included in every configuration. Confirm the required applications and licence levels before ordering.

Promira is worth evaluating when you need higher clock rates, lower signal voltages, advanced SPI modes or room to expand the tool’s capabilities.

Five questions to answer before ordering

  • Which protocol and mode do you need? Specify I2C or SPI, master or slave operation, and any Dual or Quad SPI requirement.
  • What voltage does the target use? Check signal levels separately from the target’s power supply.
  • What clock rate does the device require? Use the device’s documentation rather than selecting solely by the adapter’s maximum speed.
  • How will you run your tests? Describe whether the task involves manual commands, scripts or integration into an existing test system.
  • What might change later? Consider additional devices, interfaces or performance requirements.

A useful enquiry includes the target component’s part number, interface voltage, required clock rate and a short description of the task.

Clock speed is not the same as test throughput

A higher maximum clock rate does not automatically translate into an equally large reduction in programming or test time.

The complete operation can include command overhead, device-internal delays, erase cycles, verification and software processing. For time-sensitive applications, compare the complete sequence on representative hardware.

Our recommendation

Start with the requirements of your target device and workflow.

Evaluate Aardvark for straightforward I2C/SPI communication within its capabilities. Consider Promira when the application needs its additional performance, voltage flexibility or configurable features.

Before committing, check the complete setup—including software applications, cables and any required accessories.

Discuss your application with ISS

Not sure which configuration fits your project? Tell us what you need to connect, configure or test.

Contact ISS about your application, explore The LAB eShop or request a quotation.

Technical references

Specifications checked on 18 October 2026. Confirm the current specifications and selected application configuration before ordering.

PUT KNOWLEDGE INTO PRACTICE

Let’s talk about your application.

Buy online in The LAB eShop, or ask ISS for advice and a tailored quotation.

Shop online ↗Request a quote →

Keep exploring.

All insights →
I²C / SPI

I²C vs SPI: where to start?

A starting point for comparing interfaces and the questions that guide tool selection.

ISS Editorial TeamRead insight ↗
01 → 1000

From prototype to production.

The practical questions behind a repeatable device programming workflow.

ISS Editorial TeamRead insight ↗
SIGNAL → INSIGHT

Choose the tool. Keep the context.

Why your target, software and workflow belong in the same conversation.

ISS Editorial TeamRead insight ↗